Hi again Neil and Jeff,
It looks like the compiler complaints were warnings,
as Neil pointed out. I used the flags suggested and
it looks like the build processes is proceeding. (It
is only half way through right now, but it has surely
gone past where it was stopping before.)
Thanks for your input Neil and Jeff! Now we will be
able to see if 64 bit parallel configuration
interaction calculations are faster than 32 bit
parallel C.I. calculations on AIX/power3. I am sure
everybody is sitting at the edge of their seats to
hear the outcome! :)
-Andy Young
--- Neil Storer <Neil.Storer_at_[hidden]> wrote:
> Andy,
>
> I assume (since you're using "xlc" that you are on
> an AIX system).
>
> The error messages concerning multiply defined
> macros are only
> WARNING/INFORMATIONAL.
>
> mpcc -o A2A A2A.c
> "A2A.c", line 16.9: 1506-236 (W) Macro name TIMEOUT
> has been redefined.
> "A2A.c", line 16.9: 1506-358 (I) "TIMEOUT" is
> defined on line 15 of A2A.c.
> echo $?
> 0
>
> If they are causing hassle, you can turn off all
> error messages by including the
> "xlc" option "-w", or (BETTER STILL) you can just
> turn off these specific ones
> by using the "xlc" option:
>
> -qsuppress=1506-236:1506-358
>
> Regards
> Neil
>
> Andy Young wrote:
> > Hi Jeff,
> > Thanks for answering my post again Jeff. I looked
> > through the xlc compiler manual, but I could not
> find
> > a compiler option that will disable the behavior
> of
> > allowing only one macro definition. I do not know
> how
> > to program in C (I use fortran,) so it really is
> > possible that I overlooked something. It seems
> like
> > the options that you can give to the preprocessor
> are
> > quite limited. Most of the options you can pass
> to
> > xlc are for compiling options. So I am sort of at
> a
> > loss. Well maybe I'll look over than manual again
> and
> > see if I missed anything.
> > -Andy Young
> > JHU chemistry
> >
> >
> >
> > --- Jeff Squyres <jsquyres_at_[hidden]> wrote:
> >
> >>On Fri, 21 May 2004, Andy Young wrote:
> >>
> >>
> >>>I am confused about what to do with this make
> >>
> >>error. It says that a
> >>
> >>>macro has been already defined. I have attached
> >>
> >>the output to this
> >>
> >>>message, as well as the script that I put the
> >>
> >>configure flags into
> >>
> >>>(setuplam.s.)
> >>
> >>A tip for you with tcsh -- note that your script
> >>continued despite the
> >>fact that "make" failed.
> >>
> >>You might want to change it a little to be:
> >>
> >>/wrk2/andy/lam-7.0.4/configure ....all the
> configure
> >>args... \
> >> >& lamsetups.txt && \
> >> make >>& lamsetups.txt && \
> >> make install >>& lamsetups.txt
> >>
> >>Then "make" and "make install" will only run if
> the
> >>previous steps
> >>succeeded. Indeed, you can actually combine the
> two
> >>"make" steps by "make
> >>all install".
> >>
> >>Just a friendly tip...
> >>
> >>
> >>>This error is different than the one I was having
> >>
> >>earlier, which was
> >>
> >>>caused by an AIX xlc6.0 compiler failure under
> >>
> >>heavy optimization.
> >>
> >>This appears to be beacause we're defining the
> same
> >>macro twice. This
> >>actually doesn't cause a problem in any other
> >>compiler -- we're defining
> >>it to be the same value in both places (it's a
> long,
> >>complicated story).
> >>So in a central config header file (lam_config.h)
> >>we're #defining LAM_CC
> >>to be "xlc". Then, we're #defining it again it
> >>lam-ssi-boot-globus-config.h (to be the same
> value).
> >> This will actually
> >>happen in all the SSI subdirectories; disabling
> the
> >>globus module won't
> >>help.
> >>
> >>Is there an xlc command line parameter that can
> >>disable this error?
> >>
> >>--
> >>{+} Jeff Squyres
> >>{+} jsquyres_at_[hidden]
> >>{+} http://www.lam-mpi.org/
> >>_______________________________________________
> >>This list is archived at
> >
> > http://www.lam-mpi.org/MailArchives/lam/
> >
> >
> >
> >
> >
> > __________________________________
> > Do you Yahoo!?
> > Friends. Fun. Try the all-new Yahoo! Messenger.
> > http://messenger.yahoo.com/
> > _______________________________________________
> > This list is archived at
> http://www.lam-mpi.org/MailArchives/lam/
>
> --
>
+-----------------+---------------------------------+------------------+
> | Neil Storer | Head: Systems S/W Section
> | Operations Dept. |
>
+-----------------+---------------------------------+------------------+
> | ECMWF, | email: neil.storer_at_[hidden]
> | //=\\ //=\\ |
> | Shinfield Park, | Tel: (+44 118) 9499353
> | // \\// \\ |
> | Reading, | (+44 118) 9499000 x 2353
> | ECMWF |
> | Berkshire, | Fax: (+44 118) 9869450
> | ECMWF |
> | RG2 9AX, |
> | \\ //\\ // |
> | UK | URL: http://www.ecmwf.int/
> | \\=// \\=// |
>
+--+--------------+---------------------------------+----------------+-+
> | ECMWF is the European Centre for Medium-Range
> Weather Forecasts |
>
>
+-----------------------------------------------------------------+
>
> _______________________________________________
> This list is archived at
http://www.lam-mpi.org/MailArchives/lam/
__________________________________
Do you Yahoo!?
Friends. Fun. Try the all-new Yahoo! Messenger.
http://messenger.yahoo.com/
|
